 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PRODUCT INFORMATION CUR 3105 May/2010 CUR 3105 Hall-Effect Current Transducer The CUR 3105 is a current transducer based on the Hall effect. The IC can be used for very precise current measurements. The output voltage is proportional to the measured current and the supply voltage (ratiometric analog output). Major characteristics, such as magnetic field range, sensitivity, output quiescent voltage (output voltage at B= 0 mT), and output voltage range are programmable and are stored in the internal EEPROM. It is possible to program different transducers which are in parallel to the same supply voltage individually. The CUR 3105 features a temperaturecompensated Hall plate with choppered offset compensation, an A/D converter, digital signal processing, a D/A converter with output driver, an EEPROM memory with redundancy and lock function for the calibration data, an EEPROM for customer serial number, a serial programming interface, and protection devices at all pins. The internal digital signal processing is of great benefit because analog offsets, temperature shifts, and mechanical stress do not degrade the transducers accuracy. The CUR 3105 is programmable by modulating the supply voltage. No additional programming pin is needed. The easy programmability allows a 2-point calibration by adjusting the output voltage directly to the input signal (current). Individual adjustment of each transducer during the customer's manufacturing process is possible. With this calibration procedure, the tolerances of the IC and the mechanical positioning can be compensated in the final assembly. The calculation of the individual IC characteristics and the programming of the EEPROM memory can easily be done with a PC and the application kit from Micronas. The transducer is designed for industrial, white goods and automotive applications and operates with typically 5 V supply voltage in the wide junction temperature range from -40 C up to 170 C. The CUR 3105 is available in the very small leaded package TO92UT and the SMD package SOIC8. V V V V V V V V V V V Open-circuit (ground and supply line break detection) with 5 k pull-up and pull-down resistor, overvoltage and undervoltage detection For programming an individual transducer within several ICs in parallel to the same supply voltage, a selection can be done via the output pin Programmable clamping function Programming through modulation of the supply voltage Operates from -40 C up to 170 C junction temperature Operates from 4.5 V up to 5.5 V supply voltage in specification and functions up to 8.5 V Operates with static magnetic fields and dynamic magnetic fields up to 1 kHz Overvoltage and reverse-voltage protection at all pins Magnetic characteristics extremely robust against mechanical stress Short-circuit protected push-pull output EMC and ESD optimized design Features V V V V High-precision current transducer with ratiometric output and digital signal processing Low output voltage drifts over temperature 12-bit analog output Multiple programmable magnetic characteristics in a non-volatile memory (EEPROM) with redundancy and lock function PRODUCT INFORMATION CUR 3105 Development Tools For engineering and production purposes, Micronas offers an easy-to-use application kit: Serial Port May/2010 V V Micronas Programmer Board V 5.1 Visual Basic(R) programming software for Windows(R) 9x/2000/XP/Vista /7 HAL Programmer Board Fig. 1: Development tool setup System Architecture The CUR 3105 transducer is produced in a proven submicron CMOS technology. The CUR 3105 features a temperaturecompensated Hall plate with choppered offset compensation, an A/D converter, digital signal processing, an analog output, an EEPROM with redundancy and lock function for the calibration data and the data register information, a serial interface for programming the EEPROM, and protection devices on all pins. The CUR 3105 is programmable by modulating the supply voltage. No additional programming pin is needed. The internal digital signal processing is a great benefit because analog offsets, temperature shifts, and mechanical stress do not degrade the sensor accuracy. GND VDD Internally stabilized Supply and Protection Devices Temperature Dependent Bias Oscillator Overvoltage, Undervoltage Detection Protection Devices Switched Hall Plate A/D Converter Digital Signal Processing D/A Converter Analog Output 50 OUT EEPROM Memory Lock Control Fig. 2: Block diagram of the CUR 3105 All information and data contained in this product information are without any commitment, are not to be considered as an offer for conclusion of a contract, nor shall they be construed as to create any liability. Product or development sample availability and delivery are exclusively subject to our respective order confirmation form. By this publication, Micronas GmbH does not assume responsibility for patent infringements or other rights of third parties which may result from its use. No part of this publication may be reproduced, photocopied, stored on a retrieval system, or transmitted without the express written consent of Micronas GmbH. Edition May 14, 2010; Order No. PI000136_002EN Micronas GmbH Hans-Bunte-Strasse 19 D-79108 Freiburg (Germany) P.O. Box 840 D-79008 Freiburg (Germany) Tel. +49-761-517-0 Fax +49-761-517-2174 E-mail: docservice@micronas.com www.micronas.com |
Price & Availability of CUR3105
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |